RCA LRCR4383 príručka

(1)
  • Battery Saver
    Your universal remote control saves battery power by
    automatically turning off if any key is pressed for more than
    60 seconds. This saves your battery life should your remote
    get stuck in a place where the keys remain depressed, such as
    between sofa cushions.
    RCR3283N /
    RCR3383N
    Universal Remote Control
    Owner’s Manual
    Manual del Propietario (parte posterior)
    SAVE THIS MANUAL AND THE CODE LISTS!
    Remote controls can sometimes lose their programming
    when you change the batteries. Make sure you keep the
    manual and code lists in a safe place so that you can
    reprogram the remote if you need to.
    Tip: This remote is already programmed to operate
    most RCA-branded TVs, VCRs, DVD players and satellite
    receivers. Just press the corresponding key—DVD•VCR
    for a DVD player, TV for a television, SAT•CBL•DTC for a
    satellite receiver.
    Your universal remote requires two AAA alkaline batteries (not
    included).
    To install the batteries:
    1. Press and push the battery
    compartment cover to remove it.
    2. Insert the batteries, matching
    the batteries to the (+) and
    (–) marks inside the battery
    compartment.
    3. Push the battery cover back into
    place.
    Battery Precautions:
    Do not mix old and new batteries.
    Do not mix alkaline, standard (carbon-zinc) or
    rechargeable (nickel-cadmium) batteries.
    Always remove old, weak or worn-out batteries promptly
    and recycle or dispose of them in accordance with Local
    and National Regulations.
    To use this universal remote with your home entertainment
    system, first you need to program it to control your devices.
    There are four ways you can program the universal remote to
    operate your devices:
    The Auto Code Search goes automatically through all the
    codes for the device you’re trying to control. It’s the easiest
    method, but it can sometimes take longer than some of the
    other programming methods.
    The Brand Code Search searches through the codes for
    select brands of devices. It’s not as easy as the auto code
    search, but it can be faster.
    The Direct Code Entry lets you enter a code from the
    accompanying code list for your brand of device. It’s not as
    easy as the other methods, but it’s potentially the fastest
    method.
    The Manual Code Search lets you manually go through
    all the codes for the device you’re trying to control.
    Testing the Code for Maximum Functionality
    1. Try a variety of the device’s functions with the remote. If
    some device features don’t work, go to the next step to try
    a different code.
    2. Repeat the Auto Code Search Method from the beginning.
    When your device turns off, do not stop searching.
    Instead, with the unit now off, continue to press the PLAY
    key every 5 seconds until the unit turns back on.
    3. Once the unit turns back on, press the REVERSE key on the
    remote every 2 seconds until your device turns off again.
    When your device turns off again, press the STOP key.
    4. Test the key’s functionality again by attempting to control
    a variety of the device’s functions. If the code that has
    been stored controls the majority of the device’s functions,
    programming is complete. If the code stored does not give
    maximum functionality, try another code.
    Auto Code Search
    The Auto Code Search goes automatically through all the
    codes for the device you’re trying to control. When you nd
    the one that operates your device, you can stop the search and
    store that code.
    TIPS: Each device key is associated with a type of
    device—the TV is preset to search for TVs, SAT•CBL•DTC
    for satellite receivers, cable boxes or digital TV converters
    (DTC), and DVD•VCR for DVD players. To program a device
    key for a different type of device (for example, to program
    the DVD•VCR key to control a PVR or VCR), see the
    Reassigning the DVD•VCR Key to Control a VCR section.
    To exit without saving a new code at any point in the Auto
    Code Search, press the CLEAR key.
    1. Manually turn on the device you
    want to control.
    2. Press and hold the device key you want to program. While
    you’re holding down the device key, use your other hand
    to press and hold the remote’s POWER key at the same
    time.
    3. Wait until the remote’s indicator
    comes on and stays on. Then
    release both keys.
    4. Point the remote directly at the
    front panel of the device you
    want to control. Press PLAY on
    the remote and wait 5 seconds.
    The remote is testing a batch of
    10 codes on your device.
    Did your device turn off?
    YES: Go to step 5.
    NO: Press PLAY again. The remote tests the next batch of
    10 codes.
    Keep pressing PLAY every 5 seconds until your device turns
    off.
    5. When your device turns off, press
    the REVERSE key on the remote
    and wait at least 2 seconds.
    The remote tries the last of the
    previous ten codes.
    Did your device turn on?
    YES: Press the STOP key. You’re
    done! You’ve programmed this
    device key.
    NO: Press REVERSE again. The remote tests the next
    code in the batch.
    Keep pressing REVERSE every 2 seconds until your device
    turns back on. When it does, press STOP.
    Note: If you accidentally press the REVERSE key after your
    device turns on, press the FORWARD key. Then, wait two
    seconds to see if your device turns off again.
    NOTES
    Throughout the programming of each key, be sure to keep
    the remote pointed at the IR sensor of the device you are
    currently programming the remote to control.
    Test the remote with the device to make sure the
    device key is programmed with the correct code for
    maximum functionality. If some features don’t work, try
    a different code. See the “Testing the Code for Maximum
    Functionality” section below for more information.
    During the Auto Code Search, the remote ignores
    keypresses that aren’t part of the search.
    The search times out after two minutes (the indicator blinks
    four times and turns off, and the last programmed code
    under that device key is retained).
    The indicator blinks four times and turns off when the
    remote has gone through all the codes. The remote exits
    the Auto Code Search. If your device hasn’t turned off yet,
    try a different search method.
    Testing the Code for Maximum Functionality
    1. Try a variety of the device’s functions with the remote. If
    some device features don’t work, go to the next step to try
    a different code.
    2. Repeat the Brand Code Search from the beginning. When
    the device turns off for the first time, don’t press the STOP
    key, which would store the same code. Instead, with the
    unit now off, continue to press the POWER key repeatedly
    until the unit turns back on.
    3. Once the unit turns back on, you have found another code
    that operates the device. Press the STOP key.
    4. Test the key’s functionality again by attempting to control
    a variety of the device’s functions. If the code that has
    been stored controls the majority of the device’s functions,
    programming is complete. If the code stored does not give
    maximum functionality, try another code.
    Brand Code Search
    The Brand Code Search goes through only the codes for one of
    the select brands listed in the accompanying code list. If your
    brand of device is listed, this search can be very quick and easy.
    TIPS: Each device key is associated with a type of device—
    the TV is preset to search for TVs, SAT•CBL•DTC for satellite
    receivers, cable boxes or digital TV converters (DTC), and
    DVD•VCR for DVD players. To program a device key for
    a different type of device (for example, to program the
    DVD•VCR key to control a PVR or VCR), see the Reassigning
    the DVD•VCR Key to Control a VCR section.
    To exit without saving a new code at any point in the Brand
    Code Search, press the CLEAR key.
    1. Manually turn on the device you
    want to control.
    3. Press and hold the device key you want to program. While
    you’re holding down the device key, use your other hand
    to press and hold the remote’s POWER key at the same
    time.
    4. Wait until the remote’s indicator
    comes on and stays on. Then release
    both keys.
    6. Point the remote directly at the
    front panel of the device you want
    to control. Press POWER on the
    remote and wait 2 seconds. The
    remote is testing a single code for
    your device’s brand.
    Did your device turn off?
    YES: Press the STOP key to store the code. You’re done!
    You’ve programmed this device key.
    NO: Press POWER again. The remote tests the next code
    for your brand.
    Keep pressing POWER every 2 seconds until your device
    turns back on. When it does, press STOP.
    2. Find your device’s brand in the
    Brand Code list section of the
    accompanying code list. Circle
    the number for your brand and
    keep the list handy.
    Co d e L i ts
    Li s ta de Có di g os
    0
    1
    23
    4
    56
    7 8 9
    V
    V
    CR
    0
    1
    23
    4
    56
    7 8 9
    DV D
    SA /CABLE
    0
    1
    23
    4
    56
    7 8 9
    0
    1
    23
    4
    56
    7 8 9
    5. Look at the number you circled for
    your device’s brand code number.
    Press that number on the remote
    keypad.
    NOTES
    Throughout the programming of each key, be sure to keep
    the remote pointed at the IR sensor of the device you are
    currently programming the remote to control.
    Test the remote with the device to make sure the device
    key is programmed with the correct code for maximum
    functionality. If some features don’t work, try a different
    code. See the “Testing the Code for Maximum Functionality”
    section below for more information.
    During the Brand Code Search, the remote ignores
    keypresses that aren’t part of the search.
    The search times out after two minutes (the indicator blinks
    four times and turns off, and the last programmed code
    under that device key is retained).
    The indicator blinks four times and turns off when the
    remote has gone through all the codes. The remote exits the
    Brand Code Search. If your device hasn’t turned off yet, try a
    different search method.
    Direct Code Entry
    Direct Code Entry lets you enter a code from the accompanying
    code list for your brand of device. It’s not as easy as the other
    methods, but it’s potentially the fastest method.
    TIP: Each device key is associated with a type of device—
    the TV is preset to search for TVs, SAT•CBL•DTC for satellite
    receivers, cable boxes or digital TV converters (DTC), and
    DVD•VCR for DVD players. To program a device key for
    a different type of device (for example, to program the
    DVD•VCR key to control a PVR or VCR), see the Reassigning
    the DVD•VCR Key to Control a VCR section.
    1. Manually turn on the device you
    want to control.
    3. Press and hold the device key you want to program (the
    indicator light comes on).
    While you’re holding down the device key, use your other
    hand enter the first five-digit code for your brand in the
    code list (the indicator light goes off after the first digit).
    2. Find the Code List that came with
    the remote. Locate the section for
    the type of device you’re trying to
    program, and find your brand in
    that section. Circle the codes for
    your brand and keep them handy.
    Co d e L is ts
    Li s ta de Có di g os
    0
    1
    23
    4
    56
    7 8 9
    TV
    VC R
    0
    1
    23
    4
    56
    7 8 9
    DV D
    SA CAB LE
    0
    1
    23
    4
    56
    7 8 9
    0
    1
    23
    4
    56
    7 8 9
    NOTES
    Remember to enter the code for future reference in the box
    provided in the Code Retrieval section of this manual.
    If your brand isn’t listed in the code list, use one of the Code
    Search methods to program the remote control. (Refer to the
    Auto and Manual Code Search methods.)
    If you release the device key any time during the Direct
    Code Entry procedure, the indicator blinks four times, and
    the process is exited. The last programmed code under the
    device key is retained.
    Test the remote with the device to make sure the device
    key is programmed with the correct code for maximum
    functionality. If some features don’t work, try a different code
    in the list.
    4. When you’ve nished entering
    the five-digit code, keep holding
    down the device key and look at
    the indicator light.
    Is the indicator light on?
    YES: You’re done! You’ve programmed this device key.
    NO, it blinked four times and turned off: You have
    either entered a code number that is not in the code lists or
    missed a step in the code entry procedure. Try step 3 again.
    Indicator light
    Manual Code Search
    The Manual Code Search lets you go one-by-one through all the
    codes for the device you’re trying to control. When you nd the
    one that operates your device, you can stop the search and store
    that code.
    TIPS: The Manual Code Search method may take a long time
    because the remote searches through all of the codes in
    its memory one-by-one. If your brand is listed in the Brand
    Codes or the Code Lists, rst try the Brand Code Search or
    the Direct Code Entry method.
    Each device key is associated with a type of device—the TV is
    preset to search for TVs, SAT•CBL•DTC for satellite receivers,
    cable boxes or digital TV converters (DTC), and DVD•VCR for
    DVD players. To program a device key for a different type of
    device (for example, to program the DVD•VCR key to control
    a PVR or VCR), see the Reassigning the DVD•VCR Key to
    Control a VCR section.
    To exit without saving a new code at any point in the Manual
    Code Search, press the CLEAR key.
    Step 1: Install your batteries
    Step 2: Program your remote

Máte otázku týkajúcu sa RCA LRCR4383?

Počet otázok: 0

Tu sa jednoducho opýtajte na otázku, ktorú máte ohľadom RCA LRCR4383 od ostatných vlastníkov produktov. Poskytnite jasný a komplexný popis problému a vašej otázky. Čím bude lepšie opísaný váš problém a otázka, tým ľahšie bude pre ostatných RCA LRCR4383 vlastníkov, poskytnúť vám správnu odpoveď.

Tu si zobrazte bezplatne RCA LRCR4383 príručku. Už ste si prečítaly príručku, ale nezodpovedala vám vašu otázku? Položte svoju otázku na tejto stránke ostatným RCA LRCR4383 vlastníkom. Tu položte otázku

Produktové špecifikácie

Všeobecné
Značka RCA
Model LRCR4383
Výrobok Diaľkový ovládač
Jazyk Angličtina, Španielsky
Typ súboru PDF
Výkon
Počet podporovaných zariadení 7
Maximálny dosah -m
Súlad so smernicou RoHS -
Dizajn
Rozhranie IR Wireless
Farba Šedá
Správne použitie diaľkového ovládania AUX1, CABLE, DVD/Blu-ray, DVR, SAT, TV, VCR
Typ ovládania Tlačidlá
Počet tlačidiel 41
Obrazovka
Vstavaný displej
Hmotnosť a rozmery
Hmotnosť -g
Batérie
Nabíjateľný
Typ batérie -
Počet podporovaných batérií 2

príručky.sk

Hľadáte príručku? príručky.sk zaistí, že nájdete príručku, ktorú hľadáte, ihneď. Naša databáza obsahuje viac ako 1 milión PDF príručiek od viac ako 10 000 značiek. Každý deň pridávame najnovšie príručky, aby ste vždy našli produkt, ktorý hľadáte. Je to veľmi jednoduché: stačí do vyhľadávacieho panela napísať názov značky a typ produktu a okamžite si môžete bezplatne a online prezrieť príručku podľa svojho výberu.

príručky.sk

© Autorské práva 2020 príručky.sk. Všetky práva vyhradené.