The VP-6124-UPS is an optional unit that allows the
VP-6124/VP-6124-E to supply power during a power
outage.
The VP-6124-UPS is comprised of a VP-6124-UPS
(Charger) and a VBB-1424 (Battery Enclosure). The
VP-6124-UPS connects to the VP-6124 Power Supply
(To receive power to charge the batteries).
Listed below are specifications and recommendations
for power sources as well as precautionary
instructions.
UPS Float Standby Charging
Charging Voltage:27.6 Volts (13.8 Volts per battery)
Current Limit:900mA charging
100mA at 27 Volts final charge
Fusing:1 Amp auto-reset polyswitch
6 Amps accidental reverse battery polyswitch
Time Required to Recharge Battery
7AH Battery:14 hours
Length of Time Battery Will Provide
Power
•With four 7AH 12V batteries for 14AH total
3 Amps load draw:3 hours run time
6 Amps full load:1.5 hours run time
Use of batteries greater than 7AH is not
recommended since 90% of all power outages are less
than an hour in length and the time to evacuate a
building is less than an hour.
NOTE: To insure trouble-free UPS back-up
operation, five years batteries must be replaced five
years from the date of manufacturing.
DIMENSIONS/WEIGHT
•10.30"H x 3.50"W x 2.25"D
•(26.16cm H x 8.89cm W x 5.72cm D)
2.90 lbs. (1.32 kg)
INSTALLATION
The VP-6124-UPS (Charger) is designed for wall
mounting only. Screw the mounting plate to the wall
near the VP-6124/VP-6124-E and position the
VP-6124-UPS onto the mounting plate.
Attach the UPS unit securely to the bracket lip using
the 6-32 x 3/8" long Phillips head self-tapping screw
supplied. Place the VBB-1424 on the floor within six
feet of the unit.
CONNECTIONS
•Disconnect AC power from the power supply.
•Remove plug button from the VP-6124/VP-6124-E.
•Remove wire access cover from the
VP-6124/VP-6124-E.
•Using the cable designated by the tag labeled
Valcom P/N WA-784 with four positions
connector and attached to VP-6124-UPS
(Charger), place the Molex connector through the
hole on the power supply and connect the
charger to the Molex input connector on the
VP-6124 Power Supply.
•Snap strain relief into place.
•Replace wire access cover on the
VP-6124/VP-6124-E.
•Remove cover from Battery Backup.
•Push cable labeled Valcom P/N WA-783 with two
positions connector through the hole on the
battery enclosure and snap strain relief into
place.
Whatsapp
Mail
Facebook
Máte otázku týkajúcu sa Valcom VBB-1424?
Počet otázok: 0
Tu sa jednoducho opýtajte na otázku, ktorú máte ohľadom Valcom VBB-1424 od ostatných vlastníkov produktov.
Poskytnite jasný a komplexný popis problému a vašej otázky. Čím bude lepšie opísaný váš problém a otázka, tým ľahšie bude pre ostatných Valcom VBB-1424 vlastníkov, poskytnúť vám správnu odpoveď.
Informácie o Valcom VBB-1424
Tu si zobrazte bezplatne Valcom VBB-1424 príručku. Už ste si prečítaly príručku, ale nezodpovedala vám vašu otázku? Položte svoju otázku na tejto stránke ostatným Valcom VBB-1424 vlastníkom. Tu položte otázku
VSP-VP-6124-UPSIssue 31 947271VP-6124-UPSADD ON OPTION FOR THE VP-6124/VP-6124-EPOWER SUPPLYINTRODUCTIONThe VP-6124-UPS is an optional unit that allows theVP-6124/VP-6124-E to supply power during a poweroutage.The VP-6124-UPS is comprised of a VP-6124-UPS(Charger) and a VBB-1424 (Battery Enclosure). TheVP-6124-UPS connects to the VP-6124 Power Supply(To receive power to charge the batteries).Listed below are specifications and recommendationsfor power sources as well as precautionaryinstructions.UPS Float Standby ChargingCharging Voltage: 27.6 Volts (13.8 Volts per battery)Current Limit: 900mA charging100mA at 27 Volts final chargeFusing: 1 Amp auto-reset polyswitch6 Amps accidental reverse battery polyswitchTime Required to Recharge Battery7AH Battery: 14 hoursLength of Time Battery Will ProvidePower• With four 7AH 12V batteries for 14AH total3 Amps load draw: 3 hours run time6 Amps full load: 1.5 hours run timeUse of batteries greater than 7AH is notrecommended since 90% of all power outages are lessthan an hour in length and the time to evacuate abuilding is less than an hour.NOTE: To insure trouble-free UPS back-upoperation, five years batteries must be replaced fiveyears from the date of manufacturing.DIMENSIONS/WEIGHT• 10.30"H x 3.50"W x 2.25"D• (26.16cm H x 8.89cm W x 5.72cm D)2.90 lbs. (1.32 kg)INSTALLATIONThe VP-6124-UPS (Charger) is designed for wallmounting only. Screw the mounting plate to the wallnear the VP-6124/VP-6124-E and position theVP-6124-UPS onto the mounting plate.Attach the UPS unit securely to the bracket lip usingthe 6-32 x 3/8" long Phillips head self-tapping screwsupplied. Place the VBB-1424 on the floor within sixfeet of the unit.CONNECTIONS• Disconnect AC power from the power supply.• Remove plug button from the VP-6124/VP-6124-E.• Remove wire access cover from theVP-6124/VP-6124-E.• Using the cable designated by the tag labeledValcom P/N WA-784 with four positionsconnector and attached to VP-6124-UPS(Charger), place the Molex connector through thehole on the power supply and connect thecharger to the Molex input connector on theVP-6124 Power Supply.• Snap strain relief into place.• Replace wire access cover on theVP-6124/VP-6124-E.• Remove cover from Battery Backup.• Push cable labeled Valcom P/N WA-783 with twopositions connector through the hole on thebattery enclosure and snap strain relief intoplace.
